International supply. Engineering expertise.
office@usk.ua09:00–18:00 · Kyiv

ULTRAMIC Aluminium Nitride Heater Rated to 600 °C, 150 °C per Second

ULTRAMIC heaters are formed from aluminium nitride (AlN) with a built-in heating element, which gives a clean heat source that leaves the process uncontaminated. The lead design sets the limit at either 400 or 600 °C, and the element can warm up at 150 °C per second.

Material
aluminium nitride (AlN)
Working temperature limit
400 or 600 °C (752 or 1112 °F)
Power density
155 W/cm² (1000 W per square inch)
Heating rate
270 °F or 150 °C at the most each second

Price, availability and lead time on request. We help with analogue selection, customs clearance and delivery.

Description

The heater is built by sintering. Two pieces of unfired aluminium nitride form the body, the heating element is applied to one of them, and the two halves are then sintered into one homogeneous assembly. During sintering the ceramic powder is heated in a controlled atmosphere, producing an even grain with no open porosity. The material has a hardness of 1100 kg/mm² and a density above 99% of theoretical. The element is thermally matched to the ceramic, and the high thermal conductivity of AlN, combined with the circuit layout, gives an even surface temperature.

Aluminium nitride conducts heat almost as well as aluminium, so heat moves quickly from the element into the body. That permits a power density of 155 W/cm² (1000 W per square inch), and the element can climb as fast as 270 °F or 150 °C each second, depending on the application, the heater design and the process conditions. The homogeneous assembly suits use in air or in vacuum.

Working limits are 400 °C and 600 °C (752 °F and 1112 °F), with the figure set by the lead design. The heater also offers high electrical insulation, low leakage current and generally better chemical resistance than metal heaters.

The manufacturer offers a range of standard designs, drawn under the numbers CER-1-01 and CER-1-02, and also publishes an installation guide for ULTRAMIC heaters. The heater is fixed to the part being heated by bonding or clamping, and the configuration for a particular piece of equipment is chosen from the customer's drawing.

Technical specifications

Materialaluminium nitride (AlN)
Working temperature limit400 or 600 °C (752 or 1112 °F)
Power density155 W/cm² (1000 W per square inch)
Heating rate270 °F or 150 °C at the most each second
Ceramic hardness1100 kg/mm²
Densityabove 99% of theoretical
Operating environmentatmosphere or vacuum
Mountingbonded or clamped to the part

Part numbers

Show all part numbers (20)

CER-1-01-00001, CER-1-01-00002, CER-1-01-00003, CER-1-01-00004, CER-1-01-00005, CER-1-01-00007, CER-1-01-00093, CER-1-01-00097, CER-1-01-00098, CER-1-01-00105, CER-1-01-00333, CER-1-01-00334, CER-1-01-00335, CER-1-01-00374, CER-1-01-00540, CER-1-01-00541, CER-1-01-00542, CER-1-02-00001, CER-1-02-00002, CER-1-02-00074

Request a price and lead time

ULTRAMIC Aluminium Nitride Heater Rated to 600 °C, 150 °C per Second. We reply within one business day.

* — required fields

Or email sales@usk.ua or call 044 339-50-20.

Questions and answers

What sets the working limit at 400 or 600 °C?

The lead design of the heater. The 600 °C (1112 °F) limit applies to the corresponding lead design.

Can ULTRAMIC heaters be used in vacuum?

Yes, the heater is sintered into a homogeneous AlN assembly suitable for use in both atmosphere and vacuum.

How is the heater fixed to the part?

It is bonded or clamped to the object being heated, and the manufacturer's ULTRAMIC installation guide gives the recommendations.

Similar equipment from other manufacturers

LET’S CONNECT

Let’s start with your challenge.

Complete a short brief. We will prepare an email you can send from your own email app.

Call us044 339-50-2009:00–18:00
USK ENERGY / SEARCH

Search

Solutions, specialist directions and guides