International supply. Engineering expertise.
office@usk.ua09:00–18:00 · Kyiv

Band Type Mineral Insulated Nozzle Heater up to 760 °C, 35.6 W/cm²

A band type nozzle heater with a mineral insulated (MI) element, made for extruder heads, blown film heads and injection moulding machines. The stainless steel sheath handles up to 760 °C, with a maximum watt density of 35.6 W/cm² on small diameter nozzles.

Type
Band type nozzle heater with mineral insulation (MI)
Sheath material
Stainless steel
Maximum operating temperature
760 °C (1400 °F)
Maximum watt density
35.6 W/cm² (230 W/in²)

Price, availability and lead time on request. We help with analogue selection, customs clearance and delivery.

Description

This heater warms nozzles and cylindrical parts that need to reach temperature quickly and evenly. Typical duties include extruders, blown film heads, injection moulding machines and general barrel heating. It also suits zinc die casting machines, plastic extrusion barrels and the heating of gases, liquids or tanks. An operating limit of 760 °C allows the processing of high temperature engineering polymers.

What sets the heater apart is its mineral insulation, which conducts heat far better than the mica or solid ceramic used in conventional band heaters. A thin layer of highly conductive MI sits between the heating wire and the inner face of the sheath. A thicker layer of lower conductivity sits behind the wire and directs heat inward towards the work. Heat transfers more efficiently, the wire runs at a lower temperature, and the element should have a longer working life.

Low mass construction lets the heater respond almost at once to changes from the temperature controller, with little lag and no marked overshoot. A higher watt density shortens warm up time and supports faster production on the line.

The sheath and shroud are made of stainless steel with a side turn-down that protects the heater from plastic or other material running over the edge. Terminal clamps are permanently fixed to the heater, so separate strapping is not needed and fitting is simpler.

The maximum supply voltage is 240 V. Standard one-piece units have an inside diameter of 25 mm or 38 mm and a width of 25 mm, with a supply of 120 V or 240 V and ratings from 100 to 300 W. Terminations are available as Type B, C, E, F or H, and a typical unit weighs about 0.05 kg.

Technical specifications

TypeBand type nozzle heater with mineral insulation (MI)
Sheath materialStainless steel
Maximum operating temperature760 °C (1400 °F)
Maximum watt density35.6 W/cm² (230 W/in²)
Maximum voltage240 V
Inside diameter25 mm; 38 mm
Width25 mm
Standard voltage and power120 V or 240 V, 100–300 W
TerminationsType B, C, E, F, H
ConstructionOne-piece, terminal clamps permanently fitted

Part numbers

Show all part numbers (7)

MB1A1AN1, MB1A1AN2, MB1A1AN3, MB1A1AN4, MB1A1JN1, MB1A1JN2, MB1A1JN3

Request a price and lead time

Band Type Mineral Insulated Nozzle Heater up to 760 °C, 35.6 W/cm². We reply within one business day.

* — required fields

Or email sales@usk.ua or call 044 339-50-20.

Questions and answers

What are the maximum temperature and watt density?

The heater reaches 760 °C (1400 °F) at most, and delivers up to 35.6 W/cm² (230 W/in²) on small diameter nozzles. The maximum supply voltage is 240 V.

How does mineral insulation differ from mica?

Mineral insulation conducts heat far better than mica or solid ceramic. The wire therefore runs at a lower temperature, and the heater responds faster to the controller.

Which sizes are in the standard range?

Standard one-piece units have an inside diameter of 25 mm or 38 mm and a width of 25 mm, rated 120 V or 240 V and 100 to 300 W. Part numbers run from MB1A1AN1 to MB1A1AN4 and from MB1A1JN1 to MB1A1JN3.

Similar equipment from other manufacturers

LET’S CONNECT

Let’s start with your challenge.

Complete a short brief. We will prepare an email you can send from your own email app.

Call us044 339-50-2009:00–18:00
USK ENERGY / SEARCH

Search

Solutions, specialist directions and guides