International supply. Engineering expertise.
office@usk.ua09:00–18:00 · Kyiv

Strip-type MI heater with mineral insulation, up to 760 °C, 480 V

This strip-type heater with mineral insulation heats cylinders, nozzles and vessels from the outside. Its working temperature reaches 760 °C, the specific output is up to 15.5 W/cm2 and the voltage goes to 480 V. The sheath is 430 stainless steel.

Operating temperature
up to 760 °C (1400 °F)
Specific output
up to 15.5 W/cm2 (100 W/in2)
Maximum voltage
480 V
Sheath material
430 stainless steel

Price, availability and lead time on request. We help with analogue selection, customs clearance and delivery.

Description

The heater is fitted to extruder cylinders, blown film heads, injection moulding machines and other cylindrical parts, as well as to tanks and vessels that need external heat. A separate area is fuel cells, where it handles humidity and temperature control, fuel evaporation, heating of catalytic reactors, preheating of air for SOFC and MCFC stacks, and test rigs.

The heating wire, either coiled or serpentine, is separated from the inner face of the sheath by a thin layer of mineral insulation with high thermal conductivity. Behind the wire lies a thicker, less conductive layer that directs heat inwards towards the part. Mineral insulation conducts heat far better than the mica and solid ceramics used in conventional heaters, so the wire runs cooler and lifetime improves. The low mass gives an almost immediate response to control action, without the thermal lag and overshoot typical of ceramic-insulated heaters.

A working temperature of up to 760 °C (1400 °F) suits melting high temperature polymers such as PEEK. A specific output of up to 100 W/in2 (15.5 W/cm2) is available on large diameter bands and shortens warm-up time. The 430 stainless steel sheath has a side bend that keeps molten plastic and other flowing materials from getting in.

Designs include solid, split and two-part heaters. A split heater is made of two halves with a shared top strip, each half carrying half the total output and rated for full working voltage. The minimum internal diameter is 25 mm for lead types B, C, E and H, and 32 mm for stud leads. Lead types are B and C, which are two wires in glass fibre insulation inside a metal braid, with B turnable through 90 or 180 degrees; E, a bare metal braid; F, a glass fibre sleeve; H, a flexible steel sleeve against abrasion; K, a vertical exit where the wires can be bent close to the heater; and SLE, for split designs only, with a right-angle exit, diameter from 102 mm and width from 38 mm. Current is up to 12.5 A per wire pair, up to 17.0 A for SLE and up to 30 A per pair for studs.

Clamp plates are fixed to the heater, so separate strapping bands are not needed. Low profile clamps 6 mm in diameter with 8-32 screws are available for 25 mm and 38 mm widths. For large cylinders over 14 inches in diameter, welded nuts are recommended, as they hold a tight fit during start-up. An optional 2 mm pocket for a type J or K thermocouple to ASTM is available, and the standard lead length is 305 mm.

Technical specifications

Operating temperatureup to 760 °C (1400 °F)
Specific outputup to 15.5 W/cm2 (100 W/in2)
Maximum voltage480 V
Sheath material430 stainless steel
Insulationmineral (MI)
Lead typesB, C, E, F, H, K, SLE, studs
Current per wire pairup to 12.5 A
Current, SLE leadsup to 17.0 A
Current, studsup to 30 A per pair
Lead insulation temperature250 °C (standard), 450 °C (high temperature)
Minimum internal diameter (B, C, E, H)25 mm
Minimum internal diameter (studs)32 mm
Standard lead length305 mm
Thermocouple pocket2 mm, type J or K

Request a price and lead time

Strip-type MI heater with mineral insulation, up to 760 °C, 480 V. We reply within one business day.

* — required fields

Or email sales@usk.ua or call 044 339-50-20.

Questions and answers

What is the maximum temperature of the MI heater?

Up to 760 °C (1400 °F). The specific output of up to 15.5 W/cm2 is achieved on large diameter bands.

How does the MI heater differ from a mica heater?

Mineral insulation conducts heat much better than mica, so the wire runs cooler. Under high temperatures and specific outputs, the MI heater lasts longer than a mica heater.

Can a thermocouple be fitted into the heater?

Yes. An optional 2 mm pocket takes a type J or K thermocouple to ASTM.

Similar equipment from other manufacturers

LET’S CONNECT

Let’s start with your challenge.

Complete a short brief. We will prepare an email you can send from your own email app.

Call us044 339-50-2009:00–18:00
USK ENERGY / SEARCH

Search

Solutions, specialist directions and guides