International supply. Engineering expertise.
office@usk.ua09:00–18:00 · Kyiv

EPC2000 programmable single-loop DIN rail PID controller with Ethernet and setpoint programmer

The EPC2000 is a single-loop programmable PID controller for DIN rail mounting, with no operator panel of its own. It takes a universal input with ±0.1% of reading accuracy, offers a setpoint programmer of up to 20 programs, and has two Ethernet ports with a built-in switch.

Type
Single-loop programmable PID controller, DIN rail mounting
Control
PID with autotuning, on/off, valve positioning without position sensor
Input
1 universal input, ±0.1% of reading accuracy
Input types
Thermocouples B, J, K, L, N, R, S, T; Pt100; 0-80 mV; 0-10 V; 0-20 mA; 4-20 mA; zirconia probe

Price, availability and lead time on request. We help with analogue selection, customs clearance and delivery.

Description

The EPC2000 is built into control cabinets for furnaces, environmental chambers and other process equipment, where settings and monitoring are handled from an operator panel or a supervisory system. It performs PID control with autotuning, on/off control and valve positioning for motorised valves without a position sensor. A separate mode monitors furnace atmosphere with a zirconia oxygen probe. Typical sectors include heat treatment to AMS2750 and CQI-9, industrial furnaces, and laboratory and test equipment.

Two PID sets are provided as standard, each with its own proportional band for heating and cooling. Auto-tuning includes cutback to limit overshoot, and gain scheduling selects the PID set according to deviation from setpoint, absolute temperature, output level and other conditions. Feed-forward from PV and SP is available. The setpoint programmer offers 1x8, 1x24, 10x24 and 20x8 program and segment layouts with text names, holdback, up to eight event outputs per segment, and six configurable alarms. Five recipes of 40 parameters each can be switched from a digital input.

The universal input accepts thermocouple types B, J, K, L, N, R, S and T plus two downloadable custom curves, Pt100, 0-80 mV, 0-10 V, 0-20 mA, 4-20 mA and a zirconia probe. Sampling is 20 Hz for mV and mA, 16 Hz for thermocouples and 10 Hz for RTDs, and a sensor break is detected within three seconds. Outputs are a Form A relay, a Form C relay, a logic output for driving a solid state relay or a 0-10 V or 0-20 mA analogue output, and two dry contact inputs. Relay contacts are rated up to 2 A at 264 V ac.

Communication runs through two RJ45 Ethernet ports with a built-in 10/100BASE-T switch, supporting Modbus TCP and EtherNet/IP, with PROFINET IO in a separate version. Modbus RTU runs over optional EIA-485, and the Modbus master function polls up to three Modbus TCP slave devices and up to 32 data points. Access is protected by an 8-character password that locks after five failed attempts.

The controller runs on 24 V ac or dc at 6 W. The body is 32.6 mm wide and 111 mm high, 131.2 mm with terminals, and 107.3 mm deep, weighs 210 grams, and mounts on EN50022 DIN rail or a surface, vertically only, with no gap needed between units. It operates from 0 to 55°C at 5-90% humidity without condensation, up to 2000 metres, and carries IP20 protection with all connector plugs fitted.

Technical specifications

TypeSingle-loop programmable PID controller, DIN rail mounting
ControlPID with autotuning, on/off, valve positioning without position sensor
Input1 universal input, ±0.1% of reading accuracy
Input typesThermocouples B, J, K, L, N, R, S, T; Pt100; 0-80 mV; 0-10 V; 0-20 mA; 4-20 mA; zirconia probe
Sampling rate20 Hz mV/mA, 16 Hz thermocouples, 10 Hz RTDs
OutputsForm A relay, Form C relay, logic output or 0-10 V / 0-20 mA analogue output
Relay loadUp to 2 A at 264 V ac
Digital inputs2 dry contact inputs
Setpoint programmer1x8, 1x24, 10x24, 20x8; up to 8 event outputs per segment
Alarms and recipes6 alarms; 5 recipes of 40 parameters
Ethernet2 x RJ45, 10/100BASE-T, built-in switch
ProtocolsModbus TCP, Modbus RTU (EIA-485), EtherNet/IP, PROFINET IO
Power24 V ac / 24 V dc, 6 W
Dimensions32.6 x 111 mm (131.2 mm with terminals), depth 107.3 mm
Weight210 g
Operating temperature0...55°C
Ingress protectionIP20 with connector plugs fitted
StandardsEN 61326-1, EN 61010-1, UL 61010-1, EN ISO 13849-1

Request a price and lead time

EPC2000 programmable single-loop DIN rail PID controller with Ethernet and setpoint programmer. We reply within one business day.

* — required fields

Or email sales@usk.ua or call 044 339-50-20.

Questions and answers

Is the EPC2000 suitable for heat treatment to AMS2750?

Yes, it has ±0.1% of reading input accuracy and a setpoint programmer of up to 20 programs, and it suits furnaces that must meet AMS2750 and CQI-9.

Which industrial networks does the controller support?

Modbus TCP and EtherNet/IP through its two Ethernet ports with built-in switch, PROFINET IO in a separate version, and Modbus RTU over optional EIA-485.

What supply does the EPC2000 need?

24 V ac or dc, drawing 6 W.

Similar equipment from other manufacturers

LET’S CONNECT

Let’s start with your challenge.

Complete a short brief. We will prepare an email you can send from your own email app.

Call us044 339-50-2009:00–18:00
USK ENERGY / SEARCH

Search

Solutions, specialist directions and guides