International supply. Engineering expertise.
office@usk.ua09:00–18:00 · Kyiv

6400TSG Total Sulphur Analyser for Fuel Gas, UV Fluorescence, Ex px Cabinet

An on-line system that burns a fuel-gas sample in a flame converter and reads the resulting SO2 by UV fluorescence, giving a continuous total sulphur figure. Analyser, converter and sample handling share one pressurised steel cabinet certified for hazardous areas.

Measured value
total sulphur in fuel gas
Method
UV fluorescence after flame converter
Range
0–1 ppm (H2 only) or 0–10 ppm up to 0–500 ppm
Repeatability
±2% of full scale

Price, availability and lead time on request. We help with analogue selection, customs clearance and delivery.

Description

Each unit is set up and calibrated at the factory for a single range. The top range is 0–500 ppm total sulphur; the bottom is 0–1 ppm, but only when the stream is 100% hydrogen, otherwise the lowest available range is 0–10 ppm. Repeatability is ±2% of full scale, zero and span noise stay under 1%, drift is 2% of full scale per week, and the reading reaches 90% in less than 100 seconds at the standard 5 l/min sample flow.

The method follows ASTM D6667. Three main assemblies do the work: the 6400E UV fluorescence SO2 analyser, a flame combustion converter module (FCCM) and the sample conditioning. Switching between process sample and calibration gases is left to the operator's own control system, which the cabinet interfaces with.

The cabinet is marked Ex px IIC T3 Gb against EN 60079-0:2009 and EN 60079-2:2007, under certificate ITS11ATEX17425X. A floor-standing build with three certified viewing windows and a wall-hung build with one are covered; purging needs at least 340 SLPM of nitrogen or air from a 4 to 5.5 bar supply, for 6 minutes on the floor version and 10 minutes on the wall version, or 15 minutes with N2.

Utilities are sulphur-free UHP air for the converter at 40 psi and 1 l/min, dryer air at 25 psi and 3 l/min with a -40°C dew point, sulphur-free UHP hydrogen at 40 psi, purge gas at 40 psi, plus zero and span gases. Power is 110 or 220 V AC, 50/60 Hz, 500 W. The isolated 4–20 mA signal drives loads up to 500 ohms, and one system alarm plus two Form-C concentration relays rated 3 A at 125 V AC are fitted. Ambient operating range is 5°C to 40°C.

Technical specifications

Measured valuetotal sulphur in fuel gas
MethodUV fluorescence after flame converter
Range0–1 ppm (H2 only) or 0–10 ppm up to 0–500 ppm
Repeatability±2% of full scale
Response time90% in under 100 s
Zero/span drift2% of full scale per week
Sample flow5 l/min
Output4–20 mA, isolated, up to 500 ohms
Alarms1 system + 2 Form-C relays, 3 A, 125 V AC
Power110 or 220 V AC, 50/60 Hz, 500 W
Hazardous-area markingEx px IIC T3 Gb
Purge340 SLPM minimum, 4–5.5 bar supply
Operating temperature5°C to 40°C
ComplianceASTM D6667

Request a price and lead time

6400TSG Total Sulphur Analyser for Fuel Gas, UV Fluorescence, Ex px Cabinet. We reply within one business day.

* — required fields

Or email sales@usk.ua or call 044 339-50-20.

Questions and answers

What is the lowest range available?

0–1 ppm total sulphur, but only for a 100% hydrogen stream; for other gases the lowest range is 0–10 ppm.

Can the cabinet go into a Zone 1 area?

It carries Ex px IIC T3 Gb marking under EN 60079-0 and EN 60079-2, so it is intended for gas atmospheres requiring Gb equipment.

Which support gases does it consume?

Sulphur-free UHP air for the converter, dryer air, sulphur-free UHP hydrogen, nitrogen or air for purging, and zero and span calibration gases.

Similar equipment from other manufacturers

LET’S CONNECT

Let’s start with your challenge.

Complete a short brief. We will prepare an email you can send from your own email app.

Call us044 339-50-2009:00–18:00
USK ENERGY / SEARCH

Search

Solutions, specialist directions and guides