International supply. Engineering expertise.
office@usk.ua09:00–18:00 · Kyiv

Kjellberg InFocus Pluspole TIG torch for aluminium on positive polarity, 450 A at 100% duty cycle

Kjellberg InFocus Pluspole runs in the TIG process on direct current with the electrode on positive polarity (DC-EP) and is built for welding aluminium. The torch gives productivity close to MIG with TIG weld quality, and it welds sheet up to 8 mm in a single pass.

Brand
Kjellberg
Country of manufacture
Germany
Model
InFocus Pluspole
Type
TIG torch for positive polarity welding (DC-EP)

Price, availability and lead time on request. We help with analogue selection, customs clearance and delivery.

Description

Kjellberg presents the InFocus Pluspole as a new generation of aluminium welding. The process works on positive electrode polarity only, so the polarity never has to be switched. The cathode spot keeps cleaning the oxide film off the aluminium, which leaves a clean weld, and the output approaches MIG while the weld keeps the quality expected from TIG.

The torch and its electrodes handle up to 450 A at 100% duty cycle with the VARIGON S focusing gas, and the maximum current is 500 A. That is enough to weld sheet up to 8 mm in one pass without any edge preparation, a clean saw cut being sufficient.

The design uses a concentric two-gas system with argon as the shielding gas and a separate focusing gas. The focusing gases named by the manufacturer are VARIGON S and MISON Ar (Ar + 300 ppm O2 or NO), along with VARIGON He50S and MISON He50 (Ar / He 50 / 50 + 300 ppm O2 or NO). The arc is highly concentrated. Ignition is high frequency, cooling is liquid through a KJELLFROST cooler, the clamping diameter is 44 mm, and the torch weighs 0.7 kg without its hose pack.

Kjellberg compares the torch with conventional TIG welding of aluminium and points to several gains: no change of polarity, less helium consumed, higher output with a lower total heat input, a better ratio of penetration depth to bead width, less smoke and spatter in the workshop, a narrower heat-affected zone and smaller distortion. Electrodes are changed quickly, with no grinding or setting needed.

The FocusTIG 550 PP and FocusTIG 550 PP AC/DC power sources supply 5 - 550 A DC, 10.2 - 32 V and a pulsed mode from 0.025 Hz to 15 kHz. At 40 °C they deliver 550 A at 60% duty cycle or 420 A at 100%. Both are prepared for a cold-wire feed and have a parameter display with an adjustment wheel, two parallel gas valves, an external ignition interface and a fast shut-off when coolant flow is too low. The AC/DC model stands on a pallet base. The system can be extended with the C5S-V1 cooling unit, which has built-in flow monitoring, analogue, digital or bus control interfaces, sensors for torch guidance and height control, parameter software for the power source over USB, holders for robots and gantries with a cold-wire feed, and cameras for viewing the process. Kjellberg also offers weld task analysis, trial welds, metallography and process diagnostics.

Technical specifications

BrandKjellberg
Country of manufactureGermany
ModelInFocus Pluspole
TypeTIG torch for positive polarity welding (DC-EP)
Max. welding current500 A
Current at 100% duty cycle450 A (focusing gas VARIGON S)
Shielding gasAr
Focusing gasesVARIGON S, MISON Ar (Ar + 300 ppm O2 / NO); VARIGON He50S, MISON He50 (Ar / He 50 / 50 + 300 ppm O2 / NO)
Ignitionhigh frequency
Torch coolingKJELLFROST coolant
Clamping diameterØ 44 mm
Weight without hose pack0.7 kg
Compatible power sourcesFocusTIG 550 PP, FocusTIG 550 PP AC/DC
Power source current5 - 550 A DC
Welding voltage10.2 - 32 V
Pulsed mode0.025 Hz - 15 kHz
Power source current at 40 °C550 A at 60% duty cycle, 420 A at 100% duty cycle
Open circuit voltage79 V
Mains3 x 400 V + N + PE (-25% to +20%), 50 / 60 Hz
Fuse, slow-blow3 x 35 A
Max. connected power22.2 kVA
Recommended generator39.4 kVA
Power source protection ratingIP 23
Dimensions / weight FocusTIG 550 PP780 x 375 x 625 mm, 86,8 kg
Dimensions / weight FocusTIG 550 PP AC/DC930 x 456 x 1257 mm, 169 kg
Cooling unitC5S-V1 with flow monitoring

Request a price and lead time

Kjellberg InFocus Pluspole TIG torch for aluminium on positive polarity, 450 A at 100% duty cycle. We reply within one business day.

* — required fields

Or email sales@usk.ua or call 044 339-50-20.

Questions and answers

What thickness of aluminium can the InFocus Pluspole weld in one pass?

Sheet up to 8 mm without edge preparation, where a clean saw cut is enough. The current at 100% duty cycle is 450 A.

Why weld aluminium TIG on positive polarity?

With DC-EP the cathode spot keeps removing the oxide film from the aluminium, and no change of polarity is needed. The output approaches MIG while the weld keeps TIG quality.

Which gases does the InFocus Pluspole need?

Argon as the shielding gas, plus a focusing gas such as VARIGON S, MISON Ar, VARIGON He50S or MISON He50 with 300 ppm O2 or NO added.

Similar equipment from other manufacturers

LET’S CONNECT

Let’s start with your challenge.

Complete a short brief. We will prepare an email you can send from your own email app.

Call us044 339-50-2009:00–18:00
USK ENERGY / SEARCH

Search

Solutions, specialist directions and guides